QALCOSONIC E3 is designed for commercial accounting of heating and cooling energy when heating media is water and is used in centrally heated objects: residential houses or heat supply objects.
Integrated into the front panel of calculator. It is designed
for data reading via M-bus protocol and parameterization
of the meter.
The internal radio provides data reading via WMBUS telegram:
S1, T1 OMS mode, LoRa
WMBUS telegram:
Time of storage of all measured integral data, also without power supply to the electronic unit: at least 15 years
| Flow rate sensor | qp [m3/h] | 0.6 / 1.0 / 1.5 / 2.5 / 3.5 / 6.0 / 10 / 15 / 25 / 40 / 60 |
| R qp/qi [m3/h] | 100/250 | |
| Resolution of flow-rate indicators: | 00000,001 m3 | |
| Technical data | LCD Display | 8-digit |
| Protection class [IP] | IP65/67/68 | |
| Ambient class | Class B / EN 14 154 | |
| Ambient temperature | +5°C...+65°C | |
| Units (selectable by the user when installing): | kWh; MWh; GJ; Gcal; m3 | |
| Resolution of energy indicators (selectable by the user when installing): | 000000,01 kWh, 0000000,1 kWh, 00000001 kWh, 00000,001 MWh (Gcal or GJ) 000000,01 MWh (Gcal or GJ) |
|
| Installation position | all installation positions (vertical, horizontal, rising pipe, down pipe) |
|
| Nominal pressure [bar] | PN16/25 bar | |
| Pressure loss | 0,63 / (0,25) bar | |
| Battery lifetime | 15+1 years | |
| Flow sensor cable length | 1,2 m (2,5 m or 5 m – special order) | |
| Temperature sensor Pt500, two-wire connection, cable length | Up to 10 m | |
| Temperature measurement range | 0°C – 90°C, 0 0C – 130°C | |
| Mounting of calculator | Mounting on standard DIN-rail or on the wall | |
| Number of configurable pulse inputs/ outputs | 2 or no (to be specified when ordering), OB – in the operating mode; OD – in the test mode |
When the output is configured for energy, the value of its pulses can be selected from the list (depending on the rated flow qp and energy measurement units):
| Energy pulse value, when units are “kWh” or “MWh” | 0,00001 - 10 000 MWh/pulse |
| Energy pulse value, when units are “GJ” | 0,0001 - 10 000 GJ/pulse |
| Energy pulse value, when units are “Gcal” | 0,0001 - 1 000 Gcal/pulse |
| Water volume pulse value, m3/pulse | 0,001 - 10 m3/pulse |
f the meter is ordered with the pulse input-output device, then a permanently connected 1.5 m length cable is fitted in the
meter for connecting the inputs-outputs:
| Permanent flow rate qp, m3/h | Upper flow-rate qs, m3/h | Lower flow-rate qi, m3/h | Threshold value of flow rate, m3/h | Length of the flow sensor L, mm | Pressure losses at qp, kPa | Joining to the pipeline (Thread – G, flange – DN) |
|---|---|---|---|---|---|---|
| 0.6 | 1.2 | 0.006 | 0.003 | 110 | 7 | G3/4" |
| 0.6 | 1.2 | 0.006 | 0.003 | 190 | 0.9 | G1" or DN20 |
| 1 | 2 | 0.01 | 0.005 | 110 | 11.3 | G3/4" |
| 1 | 2 | 0.01 | 0.005 | 190 | 2.5 | G1" or DN20 |
| 1.5 | 3 | 0.006 | 0.003 | 110; 165 | 17.1 | G3/4" |
| 1.5 | 3 | 0.006 | 0.003 | 190 | 5.8 | G1" or DN20 |
| 1.5 | 3 | 0.015 | 0.003 | 110; 165 | 17.1 | G3/4" |
| 1.5 | 3 | 0.015 | 0.003 | 190 | 5.8 | G1" or DN20 |
| 1.5 | 3 | 0.015 | 0.005 | 130 | 7.2 | G1" |
| 2.5 | 5 | 0.01 | 0.005 | 130 | 19.8 | G1" |
| 2.5 | 5 | 0.01 | 0.005 | 190 | 9.4 | G1" or DN20 |
| 2.5 | 5 | 0.025 | 0.005 | 130 | 19.8 | G1" |
| 2.5 | 5 | 0.025 | 0.005 | 190 | 9.4 | G1" or DN20 |
| 3.5 | 7 | 0.035 | 0.017 | 260 | 4 | G1 1/4“, G1 1/2“, DN25 or DN32 |
| 3.5 | 7 | 0.014 | 0.007 | 260 | 9 | G1 1/4“, G1 1/2“, DN25 or DN32 |
| 6 | 12 | 0.024 | 0.012 | 260 | 10 | G1 1/4“, G1 1/2“, DN25 or DN32 |
| 6 | 12 | 0.06 | 0.012 | 260 | 10 | G1 1/4“, G1 1/2“, DN25 or DN32 |
| 10 | 20 | 0.04 | 0.02 | 300 | 18 | G2" or DN40 |
| 10 | 20 | 0.1 | 0.02 | 300 | 18 | G2" or DN40 |
| 15 | 30 | 0.06 | 0.03 | 270 | 12 | DN50 |
| 15 | 30 | 0.15 | 0.03 | 270 | 12 | DN50 |
| 25 | 50 | 0.1 | 0.05 | 300 | 20 | DN65 |
| 25 | 50 | 0.25 | 0.05 | 300 | 20 | DN65 |
| 40 | 80 | 0.16 | 0.08 | 300 | 18 | DN80 |
| 40 | 80 | 0.4 | 0.08 | 300 | 18 | DN80 |
| 60 | 120 | 0.24 | 0.12 | 360 | 18 | DN100 |
| 60 | 120 | 0.6 | 0.12 | 360 | 18 | DN100 |
Electronic unit: 116 mm x 32.5 mm x 90 mm
Example – flow sensor 1.6/2.5m3/h, Threaded end connections G3/4“, mounting length L=110 mm
| DN (mm) | 15 | 20 | 25 | 40 | 50 | 65 | 80 | 100 |
| L (mm) | 110/165 | 130/190 | 260 | 300 | 270 | 300 | 300 | 360 |
| H (mm) | 80 | 84/112 | 131/137 | 118/150 | 159 | 185 | 200 | 225 |
| G/Flange (DN | G3/4" | G1" or DN20 | G1 1/4" or DN25 | G2" or DN40 | DN50 | DN65 | DN80 | DN100 |
Should you require technical support for the Hiper HIU unit during this period, please contact one of our service providers in your area, who will be happy to help.
Please note, you will be required to provide the following information:
Cover: Scotland
Phone: 0141 4141411
Email: scotland@thermalcare.co.uk
Please call the office number and this will put you thought to out of hours.
Cover: London Areas
Phone: 0800 195 6468
Email: info@lhe.london
Address: Office 7, 35-37 Ludgate Hill, London RM10 8LH
Cover: England
Address: Building Centre, 26 Store Street, London, WC1E 7BT
Phone: 077 0449 7243
Email: aruna@heatweb.co.uk
Cover: Midlands, North & North Wales
Address: Unit 3 Chemical Lane Longbridge Hayes Ind Estate, Stoke-on-Trent , ST6 4BP
Phone: 01782 630656
Email: ange.holland@HMM.co.uk
Cover: London Areas
Phone: 07725920241
Email: aaron@hiumechservices.com
Address: 53A lansdowne lane , London, SE7 8TN
